Buying a Refurbished Gas Turbine: What to Check First

When a project needs power sooner than a new-build delivery slot allows, a refurbished gas turbine starts to look very attractive. It can be the right call. It can also be an expensive lesson, because "refurbished" is a sales word, not a technical grade.

This post sets out how we think about the choice between new, used and refurbished units, and the checks worth making before you sign a letter of intent.

New, used or refurbished: what the words really mean

None of these labels is an industry-wide standard. The same word can mean very different things depending on who wrote it: the original manufacturer (OEM), an independent overhaul shop or a seller.

New and new surplus

A new unit has never entered service. "New surplus" usually means it was built for a project that changed or was cancelled, and has been sitting in storage since. No operating hours does not mean ready to run: a unit that has waited years in a warehouse or yard needs its storage and preservation history checked just as carefully as a used one.

Used

A used turbine has operated, and it is sold without any claim of work done since. Its value lies almost entirely in its records: operating hours, starts, inspections and repairs. A used unit with a full history can be a better buy than a refurbished one with thin paperwork.

Refurbished, overhauled and "zero-hour"

These words mean someone has done work on the machine after use. The question is how much. A refurbishment might be a full overhaul of the gas generator and power turbine, or it might be selected parts replaced and a fresh coat of paint. "Zero-hour" should mean the engine was fully stripped, inspected, repaired to new-part limits, reassembled and tested, with a signed record that starts a new maintenance history. A meter reset on its own proves none of that.

Hours alone don't tell you the condition

Buyers often focus on the hour meter. It matters, but it is only half the story. GE Vernova's guidance on heavy-duty gas turbine maintenance (GER-3620) bases most maintenance requirements on independent counts of fired hours and starts, with inspections falling due on whichever limit is reached first.

In plain terms, a peaking unit that has started and stopped many times can be closer to its next major inspection than a baseload unit with far more hours. Ask for hours and starts together, dated, with the last inspection level named, and with the operating profile and fuel that produced them.

What a refurbishment record should show

If a seller calls a unit refurbished, ask for the documents behind the word, by serial number. A credible package will usually include:

  1. A dated work scope: which assemblies were opened, what was inspected and to which limits (new-part or service limits).
  2. A replaced-parts list: with part numbers and the source of each part, OEM or otherwise.
  3. Test results: for that serial number after the work, ideally including a run or load test.
  4. Borescope and inspection reports: before and after, for the hot section in particular.
  5. Who did the work: the workshop's name, and whether the work was done to OEM procedures.
  6. A written warranty: naming who stands behind the work and what it covers.

Remember the rest of the package

A turbine is more than its engine. The generator, gearbox, lube oil and fuel systems, inlet filtration, enclosure and controls each have their own history. An engine overhaul says nothing about a generator that has not been tested or a control system the OEM no longer supports. Ask what is included, what is excluded and what condition each item is in.

Storage and preservation: the gap most buyers miss

This is where we see the biggest risk in our part of the world. Many surplus and refurbished units sit for months, sometimes years, between shutdown and resale. In a hot, humid, coastal climate, moisture and salt air are hard on bearings, compressor blades, generator windings and control electronics.

A unit that was overhauled and then stored badly may no longer be the unit described on the refurbishment certificate. So alongside the work records, ask for:

  • Preservation records: how the unit was laid up, which preservatives or inhibitors were used, and whether the engine was sealed.
  • Storage conditions: indoors or outdoors, covered or exposed, and whether dehumidification was used.
  • Periodic checks: dated logs of rotor turning, insulation resistance tests on the generator, and inspections during storage.
  • Transport history: how and how often it has been moved, and how it was packed.

If those records don't exist, budget for a thorough inspection and possibly further work before commissioning. A known gap can be priced; an unknown one can't.

Before you pay: a short checklist

  • Define your need first: output, fuel, frequency, site conditions, and whether the unit will run baseload or cycle.
  • Get the serial number and match every document to it.
  • Have an independent inspector examine the unit, including a borescope inspection, before payment.
  • Confirm spare parts and technical support are still available for that model.
  • Check logistics early: weights, dimensions, lifting, packing and the route to site often take longer than the technical review.
  • Make sure title, payment terms and responsibility for preservation until handover are clear in writing.

Frequently asked questions

Is a refurbished gas turbine as good as new?

It can be close, but it depends entirely on the work scope. A unit fully overhauled to new-part limits, tested and warranted is very different from one with selected repairs. Judge it on the records, not the label.

What does "zero-hour" mean on a gas turbine?

It should mean the engine was completely stripped, inspected, repaired to new-part limits, reassembled and tested, with a signed record starting a new maintenance history. Ask who did the work and for the test record. It applies to the engine, not the whole package.

Should I buy a used or refurbished gas turbine?

A used unit with complete, verifiable records can be a sound buy, especially if you plan your own overhaul. A refurbished unit saves time if the work is well documented and warranted. Either way, check storage and preservation history before you commit.

Sources

  • GE Vernova, Heavy-Duty Gas Turbine Operating and Maintenance Considerations (GER-3620)

We broker and source gas turbines and power plant equipment, with refurbishment carried out by partner workshops. Call +65 9054 0100 or send us your requirements.

Next
Next

Ship Lay-Up in Singapore: Hot, Warm or Cold?